Eight Foot

But that will come later. Wrap the felt over one edge and secure it in place with a staple. Apply glue to the ends of the short pieces, and sandwich them between the longer pieces to create a box. It has a sturdy and spacious top and can easily fold up and fit in almost any closet. Cut two 1x4 boards to the width of the upper part of the newel post.

Poker Table Building Plans

Plans For Building A Poker Table

Here's the center piece cut out. It took a while to get to this point. Measure twice, cut once! I haven't cut out the 1" underside rim pieces yet. I just had to try fit the rail on the uncovered table.

Of course, I couldn't resist. I decided to go with a 1" width rim, just wide enough to keep the rail from moving around, but not too wide so that people leaning on the edge of the rail could raise the other side because of leverage. I was determined to get this done by gameday Friday. At least, to get the cover and padding done. To make the pad, I decided that rather than buy padding that goes to the edge of the table and having the rails "float" on top of the foam padding, why not just cut out the pad just for the center.

So, I started by mounting the rail, and tracing the inside of the rail to determine the pad size and shape. With the rail still in place, I sprayed the "center" of the table with spray adhesive, then sprayed the foam pad and lay it down on the table. I had to work quickly! I then put the rail back on top and cut around the inside edge of the rail to remove excess padding. With the rail removed and the excess foam cut away, this left a nice center foam pad.

I had to try fit the rail with the cover on the pad. Immediately, Oreo decided this was nice and comfortable to sit on. Many hours later of pulling and stapling the cover to the underside, I ended up with this. Only the rail padding is left now!

I started out by cutting out the foam pieces. Then, spray adhesive to the top of the rail and to the bottom of the foam pad. Wait a few secs for the glue to get tacky then join together. Glue the same way for the inner side of the rail and the outer side of the rail.

After the foam has glued well to the rail, take a hacksaw blade and cut the foam excess off. I finished most of the foam wrapping around the rail and vinyl covered most of the rail. I finished up the rest of it today.

I did the vinyl sections in 8 pieces. The 2 long pieces, and 3 x2 curved pieces for each of the round sides. When overlapping vinyl, I folded over one end glued it to itself to give it a more finished look. After wrapping, staple the vinyl to the rail. Pull the vinyl hard so you don't have too many wrinkles! Flenders Alle Bewertungen anzeigen. BaluForKanzler Alle Bewertungen anzeigen. Stefan Erlemann Alle 1. Patrick Alle Bewertungen anzeigen. Pitti Alle Bewertungen anzeigen.

Mark Andreas Giesecke Alle Bewertungen anzeigen. Der Kritiker Alle Bewertungen anzeigen. Jens Scholz Alle Bewertungen anzeigen. Jon Abraham Alle Bewertungen anzeigen.

Kriewald Alle 0 Bewertungen anzeigen. In die Hall of Fame aufgenommen. LightPro Alle Bewertungen anzeigen. Liene Alle Bewertungen anzeigen. James Pous Alle Bewertungen anzeigen. Robert Amper Alle Bewertungen anzeigen. Manfred Orlick Alle 2. Fassdaubi Alle Bewertungen anzeigen. Dodo Alle Bewertungen anzeigen.

Amazon Kunde Alle Bewertungen anzeigen. Hellwig Alle Bewertungen anzeigen. Joe "Gratias ago" Alle 1. Sven Alle Bewertungen anzeigen. Simon Kraus Alle Bewertungen anzeigen. Chrisdows Primeros Alle Bewertungen anzeigen.

Ewald Judt Alle Bewertungen anzeigen. Volker Hartung Alle Bewertungen anzeigen. Reptoid Alle Bewertungen anzeigen. Marc Stoeber Alle Bewertungen anzeigen. Wendy Alle Bewertungen anzeigen. Cover Alle 69 Bewertungen anzeigen. Chris Alle Bewertungen anzeigen. David Alle 90 Bewertungen anzeigen.

This is the Poker Tables category of information.